- Icom ic 756 pro ii to computer manual#
- Icom ic 756 pro ii to computer pro#
- Icom ic 756 pro ii to computer software#
- Icom ic 756 pro ii to computer plus#
- Icom ic 756 pro ii to computer series#
Icom ic 756 pro ii to computer pro#
Secure gently two screws on the motor clutch. ICOM IC756 PRO II III External Cooling There is a detailed description of the scope in Section The VFO of the IC-756PROII acts like a Model: IC-756 Pro. NOTE - good idea is to add small drop of machine oil, or silicon grease, but just "small" drop.Īfter reassembly the cover don't forget to check if brake nozzle fit in right direction as marked before.Īttach the motor to ATU chassis, put again attention that brake nozzle should is positioned as on the picture, with variable capacitor at his max capacitance (closed). Last thing we need is to secure upper cover of the motor - screwdriver with small 100g hammer or electric pliers will do the job. The IC-756 (non-pro) radios cannot be programmed from the computer.
Icom ic 756 pro ii to computer series#
Now you can easily enter options for any of the IC-756 PRO series radios.
Icom ic 756 pro ii to computer software#
Otherwise You'll have to open the cover again, or pray not to destroy the motor turning it by hand later. WCS-756 Programming Software for the Icom IC-756 PRO The WCS-756 Programmer is designed to give you the ease and convenience of programming the memories and set menu options of your radio from your PC.
Assure that it's almost same as on my pics.
NOTE: Before securing the cover, check orientation of the main output shaft with metal nozzle. Here are filter settings for 756 Pro II: USB Data mode filters by default (SSB-D). Helping a friend that just acquired a Navigator and is ready to enter the digital world. Looking for a link to, or someone who has, the menu settings for an Icom IC-756 Pro 2. Now all we need is to restore the motor to it's factory state starting with repaired rotor, and cooperating wheels in reverse order. IC-756 Pro 2 WSJT Menu Settings Don N7BT 3637. Digital Twin Passband Tuning An ICOM exclusive Flexibility of both: IF Shift. Let the epoxy solidify, and after few hours ( or minutes ) carefully examine the surface of the magnet, bottom and upper ring, remove any glue marks or dirt with sharp knife. IC-756 PRO II Raising the Bar by listening to our customers CL: JD.
Icom ic 756 pro ii to computer plus#
While I was doing the work, I modified the 756 to add the use of the 60m ham band to it's range of transmit frequencies.We are almost done. The Icom IC-756 Pro II is the worthy successor of the famous Icom 756, Icom 756 Pro, and covers all nine HF ham bands plus 6 meters (receive from 30 kHz.
Icom ic 756 pro ii to computer manual#
Wow.was I ever relieved to hear this!īob and I worked the deal, the faceplate assembly from his 756 arrived at my doorsteps this morning, and it's already on the rig and looking good as new. Icom IC-756 Pro III RELISTING A FEW ITEMS ORIGINAL Manual for Mosley CM-1 Receiver Alpha PA-374 Linear Amplifier icom ic- 746 pro LDG AL-100 TUNER FOR THE ALINCO W.T.B. I was about to send the front of my rig to him to have his new display kit installed (I couldn't possibly handle all the SMD soldering and such), when I got a message from Bob wa8ulw stating that he had an old 756 that had been struck by lightning and that it had a good display. GENERAL: Type: Amateur HF/VHF transceiver: Frequency range: TX: 10-160 m + WARC/50-54 MHz RX: 0.03-60 MHz: Tuning steps. In recent years, a ham Richard Rosenberger PA7FA in the Netherlands designed a replacement display for it. Back to Icom Next HF and more Last modified IC-756 Pro II SPECIFICATIONS.
I continued to put up with the problem, and it continued to get worse and worse.to the point where I could almost not read the display and had to rely on HRD and a CI-V interface to read some functions and frequency on the computer in the shack. Look how beautiful wfview is with a radio such as the Icom IC-718 I am accessing this radio remotely too Setup. They came out with the Pro-series 756's, and had no displays for the repair of the $2500+ radio I bought in '95. XGG Comms Digimode-4-Icom West Mountain Radio’s Rig Blaster-series boxes May use non-standard frequency format (IC-713, currently not supported) Despite these limitations, if you are willing to do some work, you can operate your rig remotely using wfview for the CI-V data and the audio. It has been a great radio, except that the display began to fail a few years ago and Icom would not support it.